三门核电土石方工程中深孔爆破法的应用

浙江三门核电平基工程中采用深孔台阶爆破进行土石方开挖,对底板的平整度和完整性有很高的要求,超挖不得超过20cm,不容许欠挖。为此,根据可爆性对开挖区内的岩石进行分级,分别采用不同的钻爆参数,同时采取了预留保护层爆破、无超深爆破、底部空气间隔装药等技术措施,确保了底板的开挖质量。     

Study of Pb-based and Pb-free perovskite solar cells using Cu-doped Ni1-xO thin films as hole transport material

SCAPS solar cell simulation program was applied to model an inverted structure of perovskite solar cells using Cu-doped Ni_1-xO thin films as hole transport layer. The Cu-doped Ni_1-xO film were made by co-sputtering deposition under different deposition conditions. By increasing the amount of the Cu-dopant, the film crystallinity enhanced whereas the bandgap energy decreased. The transmittance of the thin films decreased significantly by increasing the sputtering power of copper. High quality, uniform, compact, and pin-hole free films with low surface roughness were achieved. The structural, chemical, surface morphology, optical, electrical, and electronic properties of the Cu doped Ni_1-xO films were used as input parameters in the simulation of Pb-based (MAPbI_3-xCl_x) and Pb-free (MAGeI₃) perovskite solar cells. Simulation results showed that the performance of both Pb-based and Pb-free perovskite solar cell devices significantly enhanced with Cu-doped Ni_1-xO film. The highest power conversion efficiency (PCE) for the Pb-free perovskite solar cell is 8.9% which is lower than the highest PCE of 17.5% for the Pb-based perovskite solar cell.     

Numerical study on methane/air combustion characteristics in a heat-recirculating micro combustor embedded with porous media

Micro-combustor is a portable power device that can provide energy efficiently, heat recirculating is considered to be an important factor affecting the combustion process. For enhancing the heat recirculating and improving the combustion stability, we proposed a heat-recirculating micro-combustor embedded with porous media, and the numerical simulation was carried out by CFD software. In this paper, the effect of porous media materials, thickness and inlet conditions (equivalence ratio, inlet velocity) on the temperature distribution and exhaust species in the micro combustor are investigated. The results showed that compared with the micro combustor without embedded porous media (MCNPM), micro-combustor embedded with porous media (MCEPM) can improve the temperature uniformity distribution in the radial direction and strengthen the preheating capacity. However, it is found that the embedding thickness of porous media should be reasonably arranged. Setting the thickness of porous media to 15 mm, the combustor can obtain excellent comprehensive capacity of steady combustion and heat recirculating. Compared the thermal performance of Al₂O₃, SiC, and ZrO₂ porous media materials, indicating that SiC due to its strong thermal conductivity, its combustion stabilization and heat recirculating capacity are obviously better than that of Al₂O₃ and ZrO₂. With the porous media embedded in the micro combustor, the combustion has a tempering limit of more than 10 m/s, and the flame is blown out of the porous media area over 100 m/s. The reasonable equivalence ratio of CH₄/air combustion should be controlled within the range of 0.1–0.5, and “super-enthalpy combustion” can be realized.     

Comprehensive numerical investigations on the thermal performance of heat recirculating micro combustor with pin fins for micro-thermal voltaic system applications

Aiming at improving the relatively low energy output and energy conversion efficiency of the micro-thermal voltaic (MTPV) system, an innovative heat recirculating micro combustor with pin fins is designed. The effects of pin fins arrangement, hydrogen/air equivalent ratio on the energy output and performance of CHMC, HMCP and HMCI are compared and investigated. The result shows that when the V_in is 6 m/s and Φ is 1.0, the emitter power of CHMC is 72.76W, and that of HCMP and HCMI micro combustor are 75.99W and 76.35W. and the emitter efficiency of CHMC, HCMP and HCMI is 41.93%, 43.26% and 44.01%. HMCI has better energy output capability compared with CHMC and HMCP. Even though, HMCI brings a higher pressure drop, it is within the acceptable range. When the V_in is 6 m/s, the pressure drop from the pin fins only accounts for 26.4% of the total pressure drop for HMCI. Through the study of equivalent ratio, it is found that HMCI has good adaptability in different equivalent ratio range. This work provides new ideas for the development of MTPV system in the future.     

Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

Recursive algorithm for modeling non-linear etching rates in reactive plasma jet based optical surface machining of borosilicate crown glass

Application-specific optical glass properties are achieved by utilizing complex material compositions. This can be problematic in reactive plasma-assisted deterministic surface processing since a non-volatile surface layer may form depending on the glass composition, which affects the etch rate and thereby the local etching depth. In this investigation, a model algorithm is proposed to tackle some restrictions in applying fluorine-based plasma jet as etching tool utilized for freeform surface machining of optics made of complex glass composition, like borosilicate crown glass (e.g., N-BK7®). In this regard, firstly an analytical model is proposed for estimating the depth-dependent etch rate function. Subsequently, a recursive simulation algorithm is introduced for convolving the derived depth-dependent etch rate function with the given dwell time matrix to simulate a deterministic freeform generation process. By the proposed simulation algorithm, the impeding influence of the residual layer on the reduction of etching depth is computed prior to a real experiment in order to scale the local dwell time to ensure the targeted local removal. Finally, the simulated freeform shape is compared with the corresponding result of an etching experiment to validate the feasibility of the proposed approach.     

某会议室夏季工况不同送风方式下的气流组织数值模拟研究

采用数值模拟软件对××大学科技馆某小型会议室进行数值模拟,以实际测量的数据为边界条件,建立合适的数学和物理模型,得到温度场、速度场以及空气品质场等模拟结果,通过对模拟结果的对比分析,得到了最佳的气流组织设计方案,相关结论可以为室内气流组织方案设计与优化提供参考依据。     

海河平原区地下水累计可恢复超采量评价

地下水累计可恢复超采量评价对于地下水超采态势评判和超采综合治理实施都具有重要意义。本文以海河平原区为研究对象，提出超采量评价方法，旨在客观准确评价地下水累计可恢复超采量。针对浅层地下水超采量，提出生态临界水位作为传统“水位动态法”评价浅层地下水超采量的临界水位，据此得到研究区1959-2019年累计浅层超采量为869亿m³；针对深层地下水超采量，提出“不可恢复超采量”评价指标，采用地面沉降体积法评价深层地下水超采量，根据地面沉降体积计算深层承压含水层系统压密释水量体积，据此估算1970-2019年深层累计超采量为756亿m³；通过建立的一维非线性压密释水数值模型，模拟了深层承压含水层系统压密释水过程，计算得到非弹性压密释水量，评估研究区累计不可恢复超采量为558亿m³。因此本文认为，自1960年代以来，海河平原区地下水浅层和深层累计超采量1625亿m³，其中可恢复的超采量仅为1067亿m³。该研究结果可为未来地下水回补水量和南水北调规划调水量的确定提供参考。